Polypropylene is the second-most produced plastic in the world, after polyethylene. And for good reason: it delivers a combination of low cost, low density, chemical resistance, and processability that no other single polymer matches across such a wide range of applications. When engineers need a default material — PP is often where they start.

聚丙烯是世界上产量第二大的塑料,仅次于聚乙烯。这是有充分理由的:它提供了低成本、低密度、耐化学性和可加工性的组合,没有其他单一聚合物能在如此广泛的应用范围内匹敌。当工程师需要默认材料时——PP通常是起点。

Key Properties

关键性能

  • Density: 0.89–0.92 g/cm³ — the lightest of all commodity polymers
  • Melt Flow Index: Wide range (0.5–50+ g/10min) across grades
  • Tensile Strength: 25–40 MPa (neat resin)
  • Flexural Modulus: 1.0–2.0 GPa (neat resin)
  • HDT at 0.46 MPa: 80–110°C
  • Chemical Resistance: Excellent against acids, bases, and most organic solvents
  • Moisture Absorption: Negligible (<0.01%)

The ranges above are general literature values for neat polypropylene, quoted for orientation. They are not Hancore test results, and the grade you buy will sit somewhere within — or outside — them.

以上区间为未填充PP的一般文献值,仅作定位参考,不是Hancore的实测结果;您实际采购的牌号可能落在区间之内,也可能落在区间之外。

Why PP Dominates

聚丙烯的主导地位

Cost: PP is derived from propylene, a byproduct of petroleum refining and steam cracking. Its production cost per kilogram is among the lowest of any engineering-capable polymer. At scale, this cost advantage compounds into significant savings.

成本:PP来源于丙烯,是石油精炼和蒸汽裂解的副产品。其每公斤生产成本在所有具有工程能力的聚合物中最低。在规模化生产中,这一成本优势转化为显著的节约。

Processability: PP processes well on standard injection molding, extrusion, blow molding, and thermoforming equipment. Its relatively sharp melting point (~160–165°C) gives clean processing windows. It doesn't require drying under normal conditions — a practical advantage over hygroscopic polymers like PA or PET.

可加工性:PP在标准注塑、挤出、吹塑和热成型设备上加工良好。其相对尖锐的熔点(约160-165°C)提供了清洁的加工窗口。在正常条件下不需要干燥——相对于PA或PET等吸湿性聚合物,这是一个实际优势。

Versatility: From food containers to automotive battery cases, from medical syringes to industrial pipe systems, PP shows up everywhere. Homopolymer, copolymer, and impact-modified grades cover an enormous property space.

多功能性:从食品容器到汽车电池壳,从医用注射器到工业管道系统,PP无处不在。均聚物、共聚物和抗冲改性等级覆盖了巨大的性能空间。

Where PP Falls Short

聚丙烯的不足

No material is perfect. PP's limitations are well known:

没有完美的材料。PP的局限性是众所周知的:

  • Low-temperature brittleness: Unmodified PP becomes brittle below 0°C. Impact copolymers improve this but can't eliminate it entirely.
  • UV degradation: Unstabilized PP degrades rapidly under UV exposure. Carbon black or UV stabilizers are mandatory for outdoor use.
  • Modest stiffness: At 1–2 GPa, neat PP's flexural modulus is insufficient for many structural applications.
  • High thermal expansion: PP expands and contracts significantly with temperature changes — problematic for tight-tolerance parts.

What to Measure When Adding CSW to PP

PP中添加CSW时应测什么

Filler content always trades stiffness against toughness in a semi-crystalline polymer like PP, but where that trade-off lands depends on your resin grade, the loading level, the screw configuration and the impact modifier already in the compound. Rather than quote improvement percentages we have not measured, here is what to put on your trial sheet.

在PP这类半结晶聚合物中,填料含量始终存在刚性与韧性的权衡,但权衡落点取决于树脂牌号、添加量、螺杆构型以及配方中已有的抗冲改性剂。我们不引用未经实测的提升百分比,以下是建议在试制单上列出的项目。

  • Stiffness: flexural modulus (ISO 178 / ASTM D790) across a loading series, with unfilled PP as the baseline.
  • Heat resistance: HDT at 0.45 and 1.87 MPa on the same specimen set as the mechanical tests.
  • Dimensional stability: moulding shrinkage (flow and transverse) and post-mould dimensional change over the temperature range the part sees.
  • Toughness: notched Izod/Charpy impact and low-temperature brittleness — this is the property most at risk when loading is raised, so measure it rather than assume it.
  • Surface and appearance: gloss, replica and any fibre read-through at the a-surface.
  • Processing: torque and motor load, melt flow rate, and whisker length retained after compounding (SEM on the compound, not on the as-supplied powder).
  • Cost in use: calculated against your current filler system on your own prices and line speeds.
  • 刚性:以未填充PP为基准,在添加量梯度上测弯曲模量(ISO 178 / ASTM D790)。
  • 耐热性:在与力学测试同批试样上测0.45与1.87 MPa下的热变形温度。
  • 尺寸稳定性:成型收缩率(流动与垂直方向),以及制件在使用温度范围内的尺寸变化。
  • 韧性:缺口悬臂梁/简支梁冲击与低温脆性——提高添加量时最易受损的指标,应实测而非推定。
  • 表面与外观:光泽度、复模,以及A面的纤维透印情况。
  • 加工:扭矩与电机负载、熔体流动速率,以及共混后保留的晶须长度(对共混物做SEM,而非仅对来料粉末)。
  • 使用成本:按贵方价格与产线节拍,与现用填料体系一并测算。

The density picture is worth stating precisely: CSW is 2.69 g/cm³, which is close to calcium carbonate and higher than glass fibre, so adding it to PP (0.90 g/cm³) raises compound density. Any part-weight benefit comes from thinning the wall or replacing a heavier filler, and must be calculated per part.

关于密度需要准确说明:CSW密度2.69 g/cm³,与碳酸钙接近、高于玻璃纤维,因此加入PP(0.90 g/cm³)会提高体系密度。制件减重收益来自减薄壁厚或替代更重的填料,需按具体制件测算。

Common PP + CSW Applications

常见应用

  • Automotive interior trim panels and door panels
  • Battery housings and electrical enclosures
  • Home appliance components
  • Industrial pallets and containers
  • 3D printing filaments (PP-based)

Processing Tips

加工建议

CSW-filled PP compounds process on standard single-screw and twin-screw extruders. Key considerations: maintain moderate screw speeds to limit whisker breakage, use a screen pack to catch agglomerates, and ensure adequate distributive mixing through proper screw element configuration. Dry the powder before use — calcium sulfate carries crystallization water, and the pre-drying guidance on our Technical Resources page applies. Where a surface-treated grade is worth evaluating, run HM003S in parallel with HM003 on the same resin and line; its treatment specification and its measured effect on dispersion and interfacial adhesion in PP are still to be confirmed, so we do not state either as a result.

CSW填充PP配方可在标准单螺杆和双螺杆挤出机上加工。关键考虑因素:保持适中螺杆转速以抑制晶须断裂,使用过滤网捕集聚团物,并通过合理的螺杆元件组合保证足够的分散混合。使用前请干燥粉体——硫酸钙含有结晶水,具体干燥条件参见"技术资料"页面的预干燥建议。若需评估表面处理型,建议在同一树脂与同一产线上将HM003S与HM003平行试制;其表面处理剂规格及其在PP中对分散性与界面结合的实际影响仍待确认,因此我方不将其作为结论表述。

Tags: 标签: #Polypropylene #PP #MaterialSelection #CommodityPlastics #MineralFillers #CSW